This article is also posted on our e-commerce store patchcordsonline.com.
What is a booted cable?
A “booted” patch cable is a cable that has a molded plastic boot that is either integral to the connector, or “slips” on the RJ45 connector and a portion of the cable itself. Sometimes a booted cable is also referred to as a “strain-relief” cable, which is exactly the purpose of the boot…
There are two main types of boots that you will encounter, a separate boot that you can purchase to put on a cable that you’re making on your own, or when you buy a manufactured cable that has an injection-molded boot.
The injection-molded type is more efficient than slip-on boots as the injection molding process pushes the material right into the connector and around the individual wires. As you can imagine the main reason for the boot is to protect the cable and the connector from being damaged, wires being dislodged from the connector body, etc.
Booted patch cables are a better choice for applications where the cable will be connected and disconnected frequently, lasting much longer than their non-booted counterparts.
So what is a “snagless” boot
When an Ethernet cable is referred to as “snagless” it is referring to an extra part of the boot that covers the end of the locking tab. There are two common types of protectors you will encounter; Bubble and Ferrari.
The main difference between the two styles is that bubble tab protectors are harder to disengage than Ferrari tab protectors. Some people hate bubble boots because they can be frustrating when disconnecting the cable, others love them for the same reason. Ferrari boots are a good choice for high-density applications as they are much easier to disconnect when space is limited.
The locking tab of an RJ-45 connector is easily damaged or broken off, one of the most common ways to do so is when pulling a cable through a bunch of other cables. If there is no protection for the tab then the tab will become stuck (or snagged) on another cable and break off, rendering the cable useless.
What is a non-booted (crimped or assembly style) cable?
Technically every network cable starts its life as a non-booted cable. The outer jacket of the cable is stripped to the required length, the internal wires cut to the right length, put in the right order, and the connector placed on the end of the prepared cable. Once the connector is in position, it is fixed on the end by “crimping” the gold connectors onto the wires and also pushing a plastic bar inside the connector onto the cable jacket that is inside the connector for stability.
When you use this type of cable there are some advantages and disadvantages. As you can imagine the non-booted type is slightly less expensive than its booted counterpart, but the actual difference in price is minimal, sometimes only a couple of pennies depending on where you buy them from.
The non-booted type has no strain relief capabilities or protection for the locking tab on the connector. But there is one advantage to non-booted cables… They are very suited to high-density applications such as patch panels. If you have a 96 port patch panel with 96 patch cables connected to it, things are going to be a bit tight! If you are using molded booted patch cables you may run into a couple of issues…
The point at which a crimped cable is flexible is right at the point the cable exits the connector, this is not the case with a booted cable, you have the additional distance the boot takes up before it becomes flexible. This may not sound too bad, but this can make a big difference in a couple of ways. The cable will protrude further from the patch panel, due to the boot, which may make it difficult to fit into existing cable management, or could even mean that the door to the rack will not close. Additionally, the locking tab may be difficult to disengage on a booted cable in our patch panel scenario, the extra room the boot takes up can make a difference between being able to press it in enough to release the connector or not.
A word on choosing the length of a patch cord
We are mentioning this point in this article because the differences we have just described between booted and crimped play part in choosing the correct length of patch cable for your application. Anyone who is building a rack in an office or multiple racks in a data center wants to make a good job of cable management.
Untidy cables are painful to look at and are also a reflection on the installer themselves. We have seen installers meticulously measuring distances between patch panels and equipment with just plain cable, string, etc. to work out exactly what lengths to order, but this approach usually ends badly.
The length of a patch cable is measured from the end of one connector to the end of the other connector, not the length of the cable without the connectors. So why mention this in an article about booted vs. crimped cables? Well as described above, a booted cable does not flex as soon as the cable emerges from the connector because of the boot, the length of the boot is obviously part of the overall length of the cable itself.
So getting back to our installer who has just worked out he needs 300 3ft booted patch cables. When he comes to install them he suddenly finds out that hardly any of his patch cables are long enough!
So where did he go wrong? When a patch cable is booted, the cable does not bend directly at the connector body like a non-booted cable. There is the length of the boot to account for on both ends of the cable, this can reduce the overall length available between the ports he is trying to connect.
The best way to work out the needed length is simply measured as described and add 6 to 12 inches to your measurement. It will not matter that the cables will work out longer in some instances, as long as you order the same lengths it will be easy to produce a tidy and symmetrical result.